灯箱制作工艺
济南灯箱哪家好
13075398219
济南灯箱广告
灯箱制作厂家
山东广告传媒有限公司为您提供济南灯箱、济南灯箱制作、济南灯箱安装、济南灯箱广告等相关信息发布和相关资讯,敬请关注! 收藏本站联系我们
济南灯箱价格

全国服务热线

13075398219

当前位置: 首页 - 新闻中心 > 最新新闻 >

新闻中心

灯箱需要换画时应该如何操作?可以及时维护!

发布时间:2021-02-27 14:02:27 来源:http://www.jinandengxiang.com/

灯箱在使用时可以选择的类型有多种,其中比较常见的是翻盖开启的灯箱,这类灯箱在使用时可以及时更换画报,比较方便,其维护的方法也要确定好,可以在更换画报的同时进行相关的检查维护等,接下来为大家具体介绍一下济南灯箱需要换画时应该如何操作。
There are many types of light box that can be selected in use, among which the more common one is the light box with flip open. This kind of light box can be replaced in time when it is in use, which is more convenient. Its maintenance method should also be determined, and the relevant inspection and maintenance can be carried out at the same time of replacing the pictorial. Next, I will introduce how to operate Jinan light box when it needs to be replaced.
济南灯箱
Jinan light box
一、四面翻盖开启式的维护和画报更换方法。
1、 Maintenance and pictorial replacement method of four side flip open type.
1 .确定安装位置,确定安装方法(砖混墙体、挂大理石、木密度板、挂石膏板、中空玻璃板、双面悬挂等);
1. Determine the installation location and installation method (brick concrete wall, hanging marble, wood density board, hanging gypsum board, hollow glass board, double-sided suspension, etc.);
2.打开灯箱的包装,打开四面,取出透明面板,然后将灯箱放在安装位置,确保安装位置固定;
2. Open the package of the light box, open the four sides, take out the transparent panel, and then put the light box in the installation position to ensure that the installation position is fixed;
3 .固定灯箱,同时检测灯箱的照明情况,接好电源线,通电验光,待灯箱完好后固定,隐藏电源线,露出的电源线加装饰扣槽;
3. Fix the light box, detect the lighting condition of the light box, connect the power line, power on and optometry, fix the light box after it is in good condition, hide the power line, and add decorative buckle slot to the exposed power line;
4 .清洁安装时留下的灰尘,撕下导光板和面板的单面保护膜,用双面胶将图片贴在面板周围,将图片朝向灯箱内侧放置;
4. Clean the dust left during installation, tear off the single side protective film of the light guide plate and the panel, stick the picture around the panel with double-sided adhesive tape, and place the picture towards the inside of the light box;
5 .确认图片到位后,用上四边,检查器翻转并调整四角,撕下面板另一侧的保护膜,清除面板和框架上的灰尘。
5. After confirming that the picture is in place, turn over and adjust the four corners with the upper four sides, tear off the protective film on the other side of the panel, and remove the dust on the panel and frame.
6 .维修灯管和整流器时,先用自动螺丝刀拆下灯管盖槽,用相同规格的新灯管测试。
6. When repairing the lamp and rectifier, first remove the lamp cover groove with an automatic screwdriver and test with a new lamp of the same specification.
二、上下一体开口式的维护和更换画的方法。
2、 The upper and lower integrated open type maintenance and replacement method.
1 .确定安装位置。
1. Determine the installation position.
2 .打开灯箱的包装,取下整体开启自动螺丝,取下上盖,然后将灯箱放在安装位置,确保安装位置固定;
2. Open the package of the light box, remove the integral opening automatic screw, remove the upper cover, and then put the light box in the installation position to ensure that the installation position is fixed;
3 .固定灯箱,接好电源线,同时检测灯箱的照明情况,通电验光。
3. Fix the light box, connect the power line, and check the lighting condition of the light box at the same time.
4 .清理安装时留下的灰尘,撕下导光板和上盖内保护膜,用双面胶将图片粘贴在上盖内面板周围的铝面上(图片正面对面板),修复固定上盖;
4. Clean the dust left during installation, tear off the light guide plate and the inner protective film of the upper cover, paste the picture on the aluminum surface around the inner panel of the upper cover with double-sided adhesive tape (the picture is facing the panel), repair and fix the upper cover;
5 .固定上盖后,撕下面板另一侧的保护膜,将面板和边框上的灰尘清理干净,交付使用。
5. After fixing the upper cover, tear off the protective film on the other side of the panel, clean the dust on the panel and the frame, and deliver it to use.
6 .维修灯管和整流器时,先用自动螺丝刀拆下灯管盖槽,用相同规格的新灯管测试。如果不亮,更换旧整流器,增加灯管盖槽。
6. When repairing the lamp and rectifier, first remove the lamp cover groove with an automatic screwdriver and test with a new lamp of the same specification. If it doesn't light up, replace the old rectifier and add the lamp cover groove.
以上是济南灯箱需要换画时的操作方式,不同的开启方式的灯箱在换画报时也存在不同的方法,因此要确定好开启的方法,在维护时也要注意有无问题,及时进行维护解决。
The above is the operation mode of Jinan light box when it needs to change the picture. There are different ways to open the light box when it needs to change the picture. Therefore, it is necessary to determine the opening method, pay attention to whether there are problems during maintenance, and maintain and solve them in time.

相关推荐

首页首页 产品产品 电话电话 置顶置顶